raid6check(8) — Linux manual page

NAME \| SYNOPSIS \| DESCRIPTION \| EXAMPLES \| FILES \| BUGS \| COLOPHON

RAID6CHECK(8)            System Manager's Manual           RAID6CHECK(8)

NAME top

       raid6check - check MD RAID6 device for errors aka Linux Software
       RAID

SYNOPSIS top

       raid6check <raid6 device> <start stripe> <number of stripes>

DESCRIPTION top

       RAID6 devices in which one single component drive has errors can
       use the double parity in order to find out which component drive.
       The "raid6check" tool checks, for each stripe, the double parity
       consistency, reports mismatches and, if possible, which component
       drive has the mismatch.  Since it works at stripe level, it can
       report different drives with mismatches at different stripes.

       "raid6check" requires a non-degraded RAID6 MD device as first
       parameter, a starting stripe (usually 0) and the number of
       stripes to be checked.  If this third parameter is also 0, it
       will check the array up to the end.

       "raid6check" will start printing information about the RAID6,
       then for each stripe, it will report the parity rotation status.
       In case of parity mismatches, "raid6check" reports, if possible,
       which component drive could be responsible. Otherwise it reports
       that it is not possible to find the component drive.

       If the given MD device is not a RAID6, "raid6check" will, of
       course, not continue.

       If the RAID6 MD device is degraded, "raid6check" will report an
       error and it will not proceed further.

       No write operations are performed on the array or the components.
       Furthermore, the checked array can be online and in use during
       the operation of "raid6check".

EXAMPLES top

         raid6check /dev/md0 0 0
       This will check /dev/md0 from start to end.

         raid6check /dev/md3 0 1
       This will check the first stripe of /dev/md3.

         raid6check /dev/md1 1000 0
       This will check /dev/md1 from stripe 1000 up to the end.

         raid6check /dev/m127 128 256
       This will check 256 stripes of /dev/md127 starting from stripe
       128.

         raid6check /dev/md0 0 0 | grep -i error > md0_err.log
       This will check /dev/md0 completely and create a log file only
       with errors, if any.

FILES top

       "raid6check" uses directly the component drives as found in /dev.
       Furthermore, the sysfs interface is needed in order to find out
       the RAID6 parameters.

BUGS top

       Negative parameters can lead to unexpected results.

       It is not clear what will happen if the RAID6 MD device gets
       degraded during the check.

       The latest version of raid6check should always be available from

              https://www.kernel.org/pub/linux/utils/raid/mdadm/ 

       Related man pages:

       mdadm(8) mdmon(8), mdadm.conf(5), md(4).

COLOPHON top

       This page is part of the mdadm (Tool for managing md arrays in
       Linux) project.  Information about the project can be found at 
       ⟨http://neil.brown.name/blog/mdadm⟩.  If you have a bug report for
       this manual page, send it to [email protected].  This
       page was obtained from the project's upstream Git repository
       ⟨https://git.kernel.org/pub/scm/utils/mdadm/mdadm.git/⟩ on
       2024-06-14.  (At that time, the date of the most recent commit
       that was found in the repository was 2024-06-13.)  If you
       discover any rendering problems in this HTML version of the page,
       or you believe there is a better or more up-to-date source for
       the page, or you have corrections or improvements to the
       information in this COLOPHON (which is not part of the original
       manual page), send a mail to [email protected]

v1.0.0                                                     RAID6CHECK(8)