dcb-maxrate(8) — Linux manual page

NAME | SYNOPSIS | DESCRIPTION | PARAMETERS | EXAMPLE & USAGE | EXIT STATUS | SEE ALSO | REPORTING BUGS | AUTHOR | COLOPHON

DCB-MAXRATE(8)                    Linux                   DCB-MAXRATE(8)

NAME         top

       dcb-maxrate - show / manipulate port maxrate settings of the DCB
       (Data Center Bridging) subsystem

SYNOPSIS         top

       dcb [ OPTIONS ] maxrate { COMMAND | help }

       dcb maxrate show dev DEV [ tc-maxrate ]

       dcb maxrate set dev DEV [ tc-maxrate RATE-MAP ]

       RATE-MAP := [ RATE-MAP ] RATE-MAPPING

       RATE-MAPPING := { TC | all }:RATE

       TC := { 0 .. 7 }

       RATE := { INTEGER[bit] | INTEGERKbit | INTEGERMib | ... }

DESCRIPTION         top

       dcb maxrate is used to configure and inspect maximum rate at
       which traffic is allowed to egress from a given traffic class.

PARAMETERS         top

       The following describes only the write direction, i.e. as used
       with the set command. For the show command, the parameter name is
       to be used as a simple keyword without further arguments. This
       instructs the tool to show the value of a given parameter. When
       no parameters are given, the tool shows the complete maxrate
       configuration.

       tc-maxrate RATE-MAP
              RATE-MAP uses the array parameter syntax, see dcb(8) for
              details. Keys are TC indices, values are traffic rates in
              bits per second.  The rates can use the notation
              documented in section PARAMETERS at tc(8).  Note that
              under that notation, "bit" stands for bits per second
              whereas "b" stands for bytes per second. When showing, the
              command line option -i toggles between using decadic and
              ISO/IEC prefixes.

EXAMPLE & USAGE         top

       Set rates of all traffic classes to 25Gbps, except for TC 6,
       which will have the rate of 100Gbps:

       # dcb maxrate set dev eth0 tc-maxrate all:25Gbit 6:100Gbit

       Show what was set:

       # dcb maxrate show dev eth0
       tc-maxrate 0:25Gbit 1:25Gbit 2:25Gbit 3:25Gbit 4:25Gbit 5:25Gbit
       6:100Gbit 7:25Gbit

EXIT STATUS         top

       Exit status is 0 if command was successful or a positive integer
       upon failure.

SEE ALSO         top

       dcb(8)

REPORTING BUGS         top

       Report any bugs to the Network Developers mailing list
       <[email protected]> where the development and maintenance is
       primarily done.  You do not have to be subscribed to the list to
       send a message there.

AUTHOR         top

       Petr Machata <[email protected]>

COLOPHON         top

       This page is part of the iproute2 (utilities for controlling
       TCP/IP networking and traffic) project.  Information about the
       project can be found at 
       ⟨http://www.linuxfoundation.org/collaborate/workgroups/networking/iproute2⟩.
       If you have a bug report for this manual page, send it to
       [email protected], [email protected].  This page was
       obtained from the project's upstream Git repository
       ⟨https://git.kernel.org/pub/scm/network/iproute2/iproute2.git⟩ on
       2024-06-14.  (At that time, the date of the most recent commit
       that was found in the repository was 2024-06-11.)  If you
       discover any rendering problems in this HTML version of the page,
       or you believe there is a better or more up-to-date source for
       the page, or you have corrections or improvements to the
       information in this COLOPHON (which is not part of the original
       manual page), send a mail to [email protected]

iproute2                    22 November 2020              DCB-MAXRATE(8)

Pages that refer to this page: dcb(8)