NAME | LIBRARY | SYNOPSIS | DESCRIPTION | RETURN VALUE | ERRORS | STANDARDS | HISTORY | NOTES | SEE ALSO | COLOPHON |
|
|
subpage_prot(2) System Calls Manual subpage_prot(2)
subpage_prot - define a subpage protection for an address range
Standard C library (libc, -lc)
#include <sys/syscall.h> /* Definition of SYS_* constants */ #include <unistd.h> int syscall(SYS_subpage_prot, unsigned long addr, unsigned long len, uint32_t *map); Note: glibc provides no wrapper for subpage_prot(), necessitating the use of syscall(2).
The PowerPC-specific subpage_prot() system call provides the facility to control the access permissions on individual 4 kB subpages on systems configured with a page size of 64 kB. The protection map is applied to the memory pages in the region starting at addr and continuing for len bytes. Both of these arguments must be aligned to a 64-kB boundary. The protection map is specified in the buffer pointed to by map. The map has 2 bits per 4 kB subpage; thus each 32-bit word specifies the protections of 16 4 kB subpages inside a 64 kB page (so, the number of 32-bit words pointed to by map should equate to the number of 64-kB pages specified by len). Each 2-bit field in the protection map is either 0 to allow any access, 1 to prevent writes, or 2 or 3 to prevent all accesses.
On success, subpage_prot() returns 0. Otherwise, one of the error codes specified below is returned.
EFAULT The buffer referred to by map is not accessible. EINVAL The addr or len arguments are incorrect. Both of these arguments must be aligned to a multiple of the system page size, and they must not refer to a region outside of the address space of the process or to a region that consists of huge pages. ENOMEM Out of memory.
Linux.
Linux 2.6.25 (PowerPC). The system call is provided only if the kernel is configured with CONFIG_PPC_64K_PAGES.
Normal page protections (at the 64-kB page level) also apply; the subpage protection mechanism is an additional constraint, so putting 0 in a 2-bit field won't allow writes to a page that is otherwise write-protected. Rationale This system call is provided to assist writing emulators that operate using 64-kB pages on PowerPC systems. When emulating systems such as x86, which uses a smaller page size, the emulator can no longer use the memory-management unit (MMU) and normal system calls for controlling page protections. (The emulator could emulate the MMU by checking and possibly remapping the address for each memory access in software, but that is slow.) The idea is that the emulator supplies an array of protection masks to apply to a specified range of virtual addresses. These masks are applied at the level where hardware page-table entries (PTEs) are inserted into the hardware page table based on the Linux PTEs, so the Linux PTEs are not affected. Implicit in this is that the regions of the address space that are protected are switched to use 4-kB hardware pages rather than 64-kB hardware pages (on machines with hardware 64-kB page support).
mprotect(2), syscall(2) Documentation/admin-guide/mm/hugetlbpage.rst in the Linux kernel source tree
This page is part of the man-pages (Linux kernel and C library
user-space interface documentation) project. Information about
the project can be found at
⟨https://www.kernel.org/doc/man-pages/⟩. If you have a bug report
for this manual page, see
⟨https://git.kernel.org/pub/scm/docs/man-pages/man-pages.git/tree/CONTRIBUTING⟩.
This page was obtained from the tarball man-pages-6.9.1.tar.gz
fetched from
⟨https://mirrors.edge.kernel.org/pub/linux/docs/man-pages/⟩ on
2024-06-26. If you discover any rendering problems in this HTML
version of the page, or you believe there is a better or more up-
to-date source for the page, or you have corrections or
improvements to the information in this COLOPHON (which is not
part of the original manual page), send a mail to
[email protected]
Linux man-pages 6.9.1 2024-05-02 subpage_prot(2)
Pages that refer to this page: syscalls(2)